- Fluid or gas, concentration, viscosity and temperature
- Required flow at working pressure, or pressure/vacuum at target flow
- Supply voltage, current limit and available control signal
- On/off pattern, daily cycles, continuous run time and life target
- Maximum pump envelope, port direction, tubing and connector preference
- Ambient conditions, allowable noise and applicable compliance needs
- Prototype timing, pilot quantity, annual forecast and destination market
- Existing pump model, test data, circuit sketch or failure mode, if available
OEM support
A controlled path from requirement to repeat supply.
OEM development works best when performance, interfaces and validation responsibilities are defined early. Our process keeps those decisions connected from the first sample to production orders.
Best starting point
A duty point and a circuit sketchCurrent-pump references and test data also shorten selection.Development process
Six gates keep technical and commercial decisions aligned.
Each stage has a clear output, so a sample is not disconnected from the configuration ultimately ordered.
Application brief
We review the medium, hydraulic or pneumatic target, electrical limits, operating profile, installation space, schedule and volume.
Output: Requirement summary and open-issue list
Platform selection
Candidate pump families are compared at the working point, with the important assumptions and trade-offs made visible.
Output: Recommended model or short list
Sample definition
Voltage, motor, ports, leads, tubes and other project-specific details are recorded before samples are arranged.
Output: Sample specification and test focus
Product-level validation
Your team tests the pump in the actual circuit. We review results such as flow, pressure, noise, heat, priming and current draw.
Output: Issue review and specification update
Production confirmation
The approved configuration, commercial terms, inspection needs, packaging and forecast are aligned before repeat supply.
Output: Controlled order specification
Lifecycle support
Subsequent orders use the confirmed configuration, with technical questions and proposed changes tracked against it.
Output: Repeatable supply reference
Customization matrix
Customize only where the application creates value.
The base pump platform establishes feasibility. Project details then focus on integration, performance and supply requirements that matter in the finished product.
| Workstream | Typical decisions | Information from your team |
|---|---|---|
| Hydraulic / pneumatic | Flow and pressure balance, vacuum target, valve arrangement, tube route and application-matched operating point | Circuit resistance, target curve and medium |
| Electrical | Rated voltage, motor type, lead length, connector, polarity, suppression or speed-control requirements | Power source, current limit and control interface |
| Mechanical | Port direction, mounting interface, cable exit, external tubing and packaging constraints | 3D envelope, drawing or installation sketch |
| Materials | Wetted-material review for the named liquid or vapor and expected temperature range | SDS, formulation or compatibility list |
| Performance & life | Duty cycle, noise target, start-stop profile, endurance conditions and acceptance criteria | Use profile, environment and product warranty target |
| Supply | Sample quantity, pilot plan, inspection documentation, labeling, packing and forecast coordination | Project schedule, annual volume and destination |
Customer input
What to send for a useful first review.
A complete brief is helpful, but it does not need to be polished. Raw test notes and sketches are often more informative than a generic target.
Frequently asked questions
Practical answers before you start sampling.
Exact feasibility and timing are confirmed against the selected pump platform and configuration.
Can you recommend a pump when our specification is incomplete?
Yes. Share the end-product function and the values you already know. We will identify assumptions and missing tests, then recommend a starting platform rather than presenting an unqualified final selection.
Can we request samples before a volume quotation?
Yes. A sample request should still include the intended medium, operating point and voltage so the evaluated configuration is relevant to the later production program.
Which items can be customized?
Common project variables include voltage, motor or drive option, wire and connector, tube or port arrangement, mounting details and performance tuning. Feasibility, minimum quantity and lead time depend on the selected platform.
Do catalogue values guarantee performance in our product?
No catalogue can reproduce every circuit. Tubing, fittings, restrictions, enclosure, power supply, medium and temperature all influence results. Final approval should be based on testing in the customer assembly.
What is needed for a formal quotation?
Please provide the selected model or application requirement, configuration, sample or production quantity, delivery country and expected schedule. Annual volume helps us evaluate the appropriate supply basis.
Can quality documents be provided?
Available specifications, inspection records, material information and relevant manufacturing certificates can be discussed for the selected model and project stage. Tell us which documents your approval process requires.
Prepare an OEM review
Send your requirement—even if it is still evolving.We will turn the available data into a model shortlist, an open-issue list and a practical sample-validation plan.